Evco EV9323J9 Uživatelský manuál stáhnout pdf (Strana 2)

Evco S.p.A. • Code 1049323E00 • page 2/5

if functioning with 2 measurement inputs, the lower part of the dis-

play will show one of the labels given in the following table for 2

seconds:

LABEL MEANING

Pb1 temperature of the top

SP1 top set-point

tine value of the cooking timer or its count if the timer is active

Pb2 temperature of the floor

SP2 floor set-point

3.7 Temporary setting of the quantity shown by the

lower part of the display during the on state

• make sure no procedure is in progress

• press

and for 1s several times: the lower part of the display

will show one of the labels given in the tables in

paragraph 3.6 for 2 secs, after which it will show

the corresponding value.

Any power supply cut-off causes the display of the quantity estab-

lished with parameter P6 to be restored.

3.8 Chamber light switch on/off

• make sure no procedure is in progress

• press

Using the multifunction input, it is also possible to cause the same

effect caused by pressing the

key in remote mode.

If the chamber light is not managed by any digital output, pressing the

key will cause the display of the “no” indication for 1s in the lower

part of the display.

3.9 Buzzer silencing

• make sure no procedure is in progress

• press a key (the first time the key is pressed, the associated effect is not

caused).

Pressing the key also causes the deactivation of the acoustic output

and the buzzer output.

Using the multifunction input, it is also possible to deactivate the buzzer,

the acoustic output and the buzzer output in remote mode.

4 SETTINGS

4.1 Setting the type of functioning (with 1 measure-

ment input rather than 2)

To access the procedure:

• make sure that the instrument is in stand-by state and that no proce-

dure is in progress

• press

and for 4s: the upper part of the display will show

“PA”

• press

: the lower part of the display will show the correspond-

ing value

• press

or within 15s to set “743”

• press

• press and for 4s: the upper part of the display will show

“Pb”.

To modify the type of functioning:

• press

: the lower part of the display will show the correspond-

ing value.

The meaning of the values is the following:

VALUE MEANING

1 functioning with 1 measurement input (chamber probe)

2 functioning with 2 measurement inputs (top probe and

floor probe)

• press

or within 15s

• press

To exit the procedure:

• press

and for 4s.

The modification of the type of functioning does not cause

the configuration parameters default value to be restored.

4.2 Setting the instrument code

To access the procedure:

• make sure that the instrument is in stand-by state and that no proce-

dure is in progress

• press

and for 4s: the upper part of the display will show

“PA”

• press

: the lower part of the display will show the correspond-

ing value

• press

or within 15s to set “743”

• press

• press and for 4s: the upper part of the display will show

“Pb”

• press

or to select “CFG”.

To modify the instrument code:

• press

: the lower part of the display will show the correspond-

ing value

• press

or within 15s

• press

To exit the procedure:

• press

and for 4s.

The modification of the instrument code does not cause

the configuration parameters default value to be restored.

4.3 Setting the utility managed by each digital output

(only if the instrument code is set at 0)

To access the procedure:

• make sure that the instrument is in stand-by state and that no proce-

dure is in progress

• press

and for 4s: the upper part of the display will show

“PA”

• press

: the lower part of the display will show the correspond-

ing value

• press

or within 15s to set “743”

• press

• press and for 4s: the upper part of the display will show “Pb”

• press

or to select “do1”, “do2” or “do3”.

The label meaning is the following:

LABEL MEANING

do1 utility managed by the first digital output (relay K1)

do2 utility managed by the second digital output (relay K2)

do3 utility managed by the third digital output (relay K3)

To modify the utility managed by an output:

• press

: the lower part of the display will show the correspond-

ing value.

The meaning of the values is the following:

VALUE MEANING

0 not used

1 top

2 floor

3 airhole

4 steam injection

5 alarm

6 chamber light

7 cooking timer

8 acoustics

• press

or within 15s

• press

To exit the procedure:

• press

and for 4s.

If the instrument code is not set at 0, display only is

allowed but not the modification of the value correspond-

ing to the utility managed by the output.

4.4.1 Setting the work set-point (only if functioning with

1 measurement input)

• make sure that the instrument is in on state and that no procedure is

in progress

• press

: the lower part of the display will show “SP”, the upper

part the corresponding value and the LED

will flash

• press

or within 15s; see also parameters r1 and r2

• press

3 times or do not operate for 15s: the LED will switch-

off, after which the instrument will exit the procedure.

To exit the procedure in advance:

• do not operate for 15s (any modifications will be saved).

It is also possible to set the work set-point via the SP parameter.

4.4.2 Setting the top set-point and the floor set-point

(only if functioning with 2 measurement inputs)

To modify the top set-point:

• make sure that the instrument is in on state and that no procedure is

in progress

•press

: the lower part of the display will show “SP1”, the upper

part the corresponding value and the LED

will

flash

• press

or within 15s; see also parameters r1 and r2

•press

2 times or do not operate for 15s: the LED will

switch-off, after which the instrument will exit the pro-

cedure.

To modify the floor set-point:

• press

during the modification of the top set-point: the lower

part of the display will show “SP2”, the upper part the

corresponding value and the LED

will flash

• press

or within 15s; see also parameters r7 and r8

• press

: the LED will switch-off, after which the instrument

will exit the procedure.

To go back to previous levels:

• press

several times during the procedure.

To exit the procedure in advance:

• do not operate for 15s (any modifications will be saved).

It is also possible to set the top set-point via parameter SP1 and the floor

set-point via parameter SP2.

4.5 Setting the power distributed to the top and the

power distributed to the floor (only if functioning

with 1 measurement input)

To modify the power distributed to the top:

• press

during the modification of the work set-point: the lower

part of the display will show “Po1”, the upper part the

corresponding value and a proportioned number of bars

of the LED

will flash

• press

or within 15s; see also parameters c0 and c1

• do not operate for 15s: the LED

will switch-off, after which the

instrument will exit the procedure.

To modify the power distributed to the floor:

• press

during the modification of the power distributed to the

top: the lower part of the display will show “Po2”, the

upper part the corresponding value and a proportioned

number of bars of the LED

will flash

• press

or within 15s; see also parameters c0 and c1

• press

: the LED will switch-off, after which the instrument will

exit the procedure.

To go back to previous levels:

• press

several times during the procedure.

To exit the procedure in advance:

• do not operate for 15s (any modifications will be saved).

It is also possible to set the power distributed to the top through pa-

rameter Po1 and the power distributed to the floor through param-

eter Po2.

4.6 Setting the configuration parameters

To access the procedure:

• make sure that the instrument is in stand-by state and that no proce-

dure is in progress

• press

and for 4s: the upper part of the display will show “PA”

• press

: the lower part of the display will show the correspond-

ing value

• press

or within 15s to set “-19”

• press

or do not operate for 15s

• press

and for 4s: if functioning with 1 measurement input,

the upper part of the display will show “SP”; if

functioning with 2 measurement inputs, the

upper part of the display will show “SP1”.

To select a parameter:

• press

To modify a parameter:

• press

: the lower part of the display will show the correspond-

ing value

• press

or within 15s

• press

or do not operate for 15s.

To exit the procedure:

• press

and for 4s or do not operate for 60s (any modifica-

tions will be saved).

Cut the instrument power supply off after modification of

the parameters.

4.7 Restore the default value of the configuration pa-

rameters

• make sure that the instrument is in stand-by state and that no proce-

dure is in progress

• press

and for 4s: the upper part of the display will show

“PA”

• press

: the lower part of the display will show the correspond-

ing value

• press

or within 15s to set “743”

• press

or do not operate for 15s

• press

and for 4s: the upper part of the display will show

“Pb”

• press

or to select “dEF”

• press

: the lower part of the display will show the correspond-

ing value

• press

or within 15s to set “149”

• press

or do not operate for 15s: the upper part of the display

will show “dEF” flashing for 4s, after which “dEF” will

switch on

• cut the instrument power supply off.

To exit the procedure in advance:

• press

and for 4s during the procedure (i.e. before setting

“149”: restore will not be carried out).

Make sure that the default value of the parameters is

appropriate.

5 COOKING TIMER

5.1 Preliminary considerations

The cooking timer allows to start the reverse count of a time.

The count is shown in the lower part of the display; during the count

the “timer” LED is on and the timer output is activated.

Before conclusion of the count (of the time established with parameter c9)

the buzzer and the acoustic output are activated, for the time estab-

lished with parameter c4.

Before conclusion of the count (of the time established with parameter c5)

the airhole is activated, for the time established with parameter c6.

Using the multifunction input, it is also possible to start/interrupt the

cooking timer in remote mode.

5.2 Setting the cooking timer

• make sure that the instrument is in the on state, that the cooking timer

count is not in progress and that no procedure is in progress

• press

and : the lower part of the display will show the value

of the cooking timer; the left part and the “timer”

LED will flash.

The value of the cooking timer is displayed in the hours:minutes format.

To modify the hour:

• press

or within 15s

• press

: the right part will flash.

To modify the minutes:

• press

or within 15s.

The cooking timer can be set between 00:00 and 24:00 h:min.

• press

: the “timer” LED will switch-off, after which the instru-

ment will exit the procedure.

To go back to previous levels:

• press

several times during the procedure.

To exit the procedure in advance:

• do not operate for 15s (any modifications will be saved).

The cooking timer can also be set when the count is in progress (this

modification is temporary, i.e. any power supply cut-off causes the

value set with the procedure given at the start of this paragraph to be

restored). If the value is set at 00:00 h:min, the count will be inter-

rupted, the “timer” LED will switch-off and the buzzer will be activated

for 3 seconds.

5.3 Starting the cooking timer

• press

during timer setting: the “timer” LED will switch on.

Alternatively:

• make sure that the instrument is in on state and that no procedure is

in progress

• press

: the “timer” LED will switch on.

1 2 3 4 5

Komentáře k této Příručce

Žádné komentáře

Evco EV9323J9 Uživatelský manuál Strana 2

Komentáře k této Příručce

Související produkty a manuály pro Hardware Evco EV9323J9